Featured Products
Planet Finial Mandrel Kit
A brand new product designed by Planet. The Finial Mandrel fits into the tail stock and offers support for the fine end of a finial whilst turning the rest of it. The Finial Mandrel Kit has 3 Delrin (nylon type) inserts with 3 sizes 3mm, 4.5mm & 6mm hole depending on the size of Finial being turned. They fit into the inner race of a free running bearing. Available in 1MT & 2MT
£31.99 inc VAT
Planet Tarrant Light Pull Drive Kit inc stepped drill 3mm/6mm x 120mm
Planet Light Pull Drive Kit inc stepped drill 3mm/6mm x 120mm
Available in 1MT or 2MT
from £18.99 inc VAT
Planet Lathe Centre Alignment Tool
A brand new product from Planet. Aligns your headstock back with your tailstock after using it in 'outboard' mode.
from £13.99 inc VAT
Grid
List
Charnwood 1MT / 2MT Revolving Centre
Choose your size above, you will recieve one centre only
Charnwood CDC25 Crown Drive Centre For Chucks 25mm diameter
Turn spindles without removing your chuck from the lathe using this chuck drive centre.
The sharp point in the centre is spring loaded and retracts as pressure is applied from the tail stock.
The ring of 20 sharp teeth then create an extremely powerful grip.
Crown diameter 25mm (1")Overall Length 55mm (2")Diameter of Chuck Insert End 19mm (3/4")Width of Jaw Clamping Channel 9mm (3/8")
Can...
Charnwood Drive Centre
Choose your size
New Charnwood Crown Drive Centre 1mt / 2mt
New for 2018 Crown Drive Centres 1mt / 2mt
New Charnwood Crown revolving Centre 1mt / 2mt
New for 2018 Crown Drive Centres 1mt / 2mt
PEN MANDREL SUPPORT CENTRE 1 MT
The Pen Mandrel Support Centre has been designed and manufactured by PLANET here in the UK as an optimum way of holding and supporting the Pen Mandrel Shaft during the making of pens. This product is much the same as our Standard Rotating Centre (SD1/2), having 2 sealed bearings, a 12mm nose to represent 12mm bushings, is offered in 1MT & 2MT, precisely machined and designed to last and satisfy...
PEN MANDRELL SUPPORT CENTRE 2MT
The Pen Mandrel Support Centre has been designed and manufactured by PLANET here in the UK as an optimum way of holding and supporting the Pen Mandrel Shaft during the making of pens. This product is much the same as our Standard Rotating Centre (SD1/2), having 2 sealed bearings, a 12mm nose to represent 12mm bushings, is offered in 1MT & 2MT, precisely machined and designed to last and satisfy...
Planet 11222 Large Drive Centre 2 Prong 1 1/2' (38.1mm) 2MT
Suitable for all large types of spindle work.Integral points will not work loose. Removable with extractor ring.
4 prong for squared spindle ends, 2 prong for out of square spindle ends.
Planet 11242 Large Drive Centre 4 Prong 1 1/2' (38.1mm) 2MT
Suitable for all large types of spindle work.Integral points will not work loose. Removable with extractor ring.
4 prong for squared spindle ends, 2 prong for out of square spindle ends.
Planet 5161B Hollow Ring Centre 5/8' (15.9mm)
Facilitates the boring of long holes. 5/8” diameter head with 5/16” bore. Supplied complete with removable centre and hex key.
May also be used as a tail centre when there is risk of splitting.
Planet CR60 Detachable Ring Centre Accessory
May be placed over the cone of any 60 degree rotating tail centre to convert it to a rotating ring centre.
Helps prevent wood splitting due to the pressure of the centre.
Overall diameter 20mm.
Planet DX1 Deluxe Rotating Centre (60Deg) (12mm) 1MT
Slim, Deluxe Rotating Centre. 12mm dia. nose with 60 deg. point. Main body remains stationary while small point turns.
Ideal for smaller precision work as well as general spindle turning.
Triple bearing design incorporating thrust race.
Small rotating cone has been hardened to withstand against wear
Planet DX2 Deluxe Rotating Centre (60Deg) (12mm) 2MT
Slim, Deluxe Rotating Centre. 12mm dia. nose with 60 deg. point. Main body remains stationary while small point turns. Ideal for smaller precision work as well as general spindle turning.
Triple bearing design incorporating thrust race.
Small rotating cone has been hardened to withstand against wear
Planet Finial Mandrel Kit
A brand new product designed by Planet. The Finial Mandrel fits into the tail stock and offers support for the fine end of a finial whilst turning the rest of it. The Finial Mandrel Kit has 3 Delrin (nylon type) inserts with 3 sizes 3mm, 4.5mm & 6mm hole depending on the size of Finial being turned. They fit into the inner race of a free running bearing. Available in 1MT & 2MT
Planet HC2 Halved Solid Centre 2MT
Solid centre with nose ‘halved’. Facilitates turning of very small projects.
Enables tool access very close to centre.
Planet HD1 Heavy Duty Rotating Centre (60Deg) (36mm) 1MT
Heavy Duty Rotating Centre. 36mm dia. head with 60 deg. point.
Designed for heavier turning work.
Triple bearing design, incorporating a substantial thrust race.
Planet HD2 Heavy Duty Rotating Centre (60Deg) (36mm) 2MT
Heavy Duty Rotating Centre. 36mm dia. head with 60 deg. point.
Designed for heavier turning work.
Triple bearing design, incorporating a substantial thrust race.
Planet HRC1 Hollow Rotating Centre (60Deg) (31mm) 1MT
Rotating centre with 5/16” bore for long hole boring.
Based around our standard duty configuration. Also useful for spindle turning when there is a danger of a centre point splitting the stock.
Set comprises: Hollow rotating centre, nose cone for use as standard centre, centring rod.
Planet HRC2 Hollow Rotating Centre (60Deg) (31mm) 2MT
Rotating centre with 5/16” bore for long hole boring.
Based around our standard duty configuration. Also useful for spindle turning when there is a danger of a centre point splitting the stock.
Set comprises: Hollow rotating centre, nose cone for use as standard centre, centring rod.
Planet Lathe Centre Alignment Tool
A brand new product from Planet. Aligns your headstock back with your tailstock after using it in 'outboard' mode.
Planet LBD1 Lace Bobbin Drive Centre 1/2' (12.7mm) 1MT
Tapered drive for lace bobbins, etc.
Mouth of drive is 1/2” square
Planet LBD2 Lace Bobbin Drive Centre 1/2' (12.7mm) 2MT
Tapered drive for lace bobbins, etc.
Mouth of drive is 1/2” square
Planet LD1 Light Duty Rotating Centre (60Deg) (22mm) 1MT
Light Duty Rotating centre. Designed to facilitate the turning of small items. 22mm dia. head with 60 deg. point. Twin deep groove ball races.
Planet MC02A Multi Chuck Drive Centre 2 Prong 1' (25.4mm)
Designed to be held in the jaws of a multi-chuck system. Enables between-centre turning to be carried out without unmounting the chuck.
Shank Diameter 18mm
Planet MC04A Multi Chuck Drive Centre 4 Prong 1' (25.4mm)
Designed to be held in the jaws of a multi-chuck system. Enables between-centre turning to be carried out without unmounting the chuck.
Shank Diameter 18mm
Planet Piloted Drive Centre 1' (25.4mm)
1” diameter 4 prong head. Head relieved behind flutes to prevent binding. Supplied with inter-changeable point, pilot and hex key.
Planet PM3S Pen Mandrel Spares - Spacers 3pc, Brass Nut 1pc
3 x Spacers
1 x Brass Nut
Planet PM5BN Pen Mandrel Spares - Brass Nuts 5pc
Brass Nuts x 5
Planet PM5N Pen Mandrel Spares - Locking Nuts 5pc
spare components to complete your kits
Locking Nuts x 5
Planet PM5X Pen Mandrel Spares - 2 Cones, 2 Spacers, 1 Brass Nut
2 x Cones
2 x Spacers
1 x Brass Nut
Planet Standard Drive Centres 1MT
Suitable for all types of spindle work.Integral points will not work loose. Removable with extractor ring.
4 prong for squared spindle ends,
2 prong for out of square spindle ends.
Planet Standard Drive Centres 2MT
Suitable for all types of spindle work.Integral points will not work loose. Removable with extractor ring.
4 prong for squared spindle ends,
2 prong for out of square spindle ends.
Planet Standard Duty Rotating Centres (60Deg) (31mm)
Standard Duty Rotating Centre. 31mm dia. head with 60 deg. point. Excellent general purpose centre. Twin deep groove ball races.
Planet Tarrant Light Pull Drive Kit inc stepped drill 3mm/6mm x 120mm
Planet Light Pull Drive Kit inc stepped drill 3mm/6mm x 120mm
Available in 1MT or 2MT
Planet Tarrant Light Pull Drive SPARE Stepped Drill 3mm/6mm x 120mm
Planet Light Pull Drive Spare Stepped Drill 3mm/6mm x 120mm
RECORD POWER 2 PRONG CENTRE 5/8" DIAM.
Designed to hold wood securely without splitting, this drive centre gives superior hold. The opposing tooth profiles mean that as they enter the wood, the fibres are pushed together rather than apart, holding the timber together.
RECORD POWER 2MT SPUR CENTRE
2MT 4 PRONG SPUR CENTRE FOR SECURE HOLDING OF LARGE WORK.Featuring four blades with a fixed centre point, this is precision turned and milled with a special blade profile to allow excellent timber penetration and grip. Hardened for longer life. Comes standard with all Teknatool Lathes but will fit all 2MT lathes.
Record Power 4 Prong Drive Center 2MT
Record Power 4 Prong Drive Center 2MT
RECORD POWER CWA131 Long Hole Boring Kit - 1 Morse Taper
RECORD POWER CWA131 Long Hole Boring Kit - 1 Morse Taper
Record Power CWA162 Morse Taper Adaptor Sleeve (2MT to 1MT)
Sleeve for using 1 Morse Taper accessories on a 2 Morse Taper lathe.
RECORD POWER CWA80 4 Prong Drive Centre 1 MT
RECORD POWER CWA80 4 Prong Drive Centre
RECORD POWER CWA93 Live Centre - 1 Morse Taper
A good quality tailstock live centre is an essential accessory when turning between centres. Unlike traditional stationery centres, a live centre rotates with the wood, eliminating burning and increasing hold. All Record Power live centres feature high quality bearings to give long life and resist pressure during use. Sealed for life bearings ensure reliable, long lasting operation.
RECORD POWER LONG HOLE BORING KIT (2MT) WITH CWA111
The perfect tool for making long, uniform apertures through workpieces on the lathe. Ideal for lampstands, as the hole bored is 5/16”, to accept standard bulb holders.
RECORD POWER REVOLVING CENTRE (MT2 SHANK)
A good quality tailstock live centre is an essential accessory when turning between centres. Unlike traditional stationery centres, a live centre rotates with the wood, eliminating burning and increasing hold. All Record Power live centres feature high quality bearings to give long life and resist pressure during use. The sealed for life bearings ensure reliable, long lasting operation.
Record Power Spur Centre
This useful centre is held in the chuck with the 50 mm standard jaws to give a quick-mount solution for spindle turning, meaning the chuck need not be removed from the lathe.
Record Power Standard Woodworm Screw RH / LH
The SC3 and SC4 are supplied with the indispensable Record Power woodworm screw. Ideal for mounting bowl blanks, this screw is held in the jaws of the chuck, giving exceptional holding power. This means a separate wood screw chuck need not be used and the chuck can stay on the lathe, saving time and effort.
Choose from RH / LH thread above
