Planet

Planet

Planet Plus -

A family business based Chandler's Ford, Planet Plus has been a leading force in the pen turning market for many years!

All of our rotur drive center's and pen kit's are made right here in the UK!

  • display as grid Grid
  • display as list List
Page: | 1 | 2 |

Planet Forstner Extension Bar
Planet Forstner Extension Bar
Forstner Extension Bar A must have for that extra depth. 200ml (8") has a 3/8" collar 280ml (12" has a 1/2" collar
from £29.99 inc VAT
Planet Long Series Sawtooth Forstner Bit
Planet Long Series Sawtooth Forstner Bit
Long series sawtooth Forstner cutter Sawtooth pattern, particularly suited for cutting down the grain. Long series - all sizes are a minimum of 150mm long, will produce over-lapping holes, resharpenable.
from £11.99 inc VAT

Planet  Thread Adaptor - M33 x 3.5mm Female to 1'x8tpi Male
Planet Thread Adaptor - M33 x 3.5mm Female to 1'x8tpi Male
Planet Thread Adaptor - M33 x 3.5mm Female to 1"x8 tpi Male
£21.99 inc VAT
Planet  Thread Adaptor - M33 x 3.5mm Female to 3/4' x 16tpi Male
Planet Thread Adaptor - M33 x 3.5mm Female to 3/4' x 16tpi Male
Planet Thread Adaptor - M33 x 3.5mm Female to 3/4" x 16tpi Male
£21.99 inc VAT

Planet Morse Taper Adaptor Sleeve MT2-MT1
Planet Morse Taper Adaptor Sleeve MT2-MT1
Converts morse taper 2 spindles to Morse Taper 1
£4.99 inc VAT
Planet PM3S Pen Mandrel Spares - Spacers 3pc, Brass Nut 1pc
£6.99 inc VAT

Planet Tailstock Knockout Bar 265mm
Sold Out
Planet Tailstock Knockout Bar 265mm
Tailstock Knock Out Bar
£3.99 inc VAT
Planet Cabinet Scraper 4' x 2'
Planet Cabinet Scraper 4' x 2'
cabinet scraper for difficult grain
£6.99 inc VAT

Planet Cabinet Scraper 5' x 2 1/2'
Planet Cabinet Scraper 5' x 2 1/2'
scraper for tricky grain or difficult to reach areas
£6.99 inc VAT
Planet Cabinet scraper set
Planet Cabinet scraper set
A cabinet scraper is a key tool that removes small amounts of material. It does especially well in tricky areas of hardwoods where traditional hand planes would cause tear-out. Manufactured in Sheffield from flexible,high quality steel, and polished to give a smooth finish. They have a good edge retention and are re-sharpenable Set includes: rectangle, concave/convex, kidney.
£19.99 inc VAT

Marking Gauge 150mm
Marking Gauge 150mm
Mark perfect joints every time. The extra sharp replaceable cutter is hardened and marks a keen accurate line, preventing grain tear out during material removal. Up to 150mm depth of adjustment. Lightweight aluminum body with bright brass standard face. Engraved inch measurements on precision ground shaft.
£33.99 inc VAT
Planet 3 (75mm) Steel Centre Square
Planet 3 (75mm) Steel Centre Square
Planet 3″ Steel Center Square, ideal for precision center-finding in engineering tasks or spindle marking
£19.99 inc VAT

Planet Depth Gauge 6 Inches
Planet Depth Gauge 6 Inches
Traditional design. Full 6” / 150mm depth check. Etched and filled rule.
£9.99 inc VAT
Planet Drill Gauge 2 Piece Set Metric and ImperialPlanet Drill Gauge 2 Piece Set Metric and Imperial
Planet Drill Gauge 2 Piece Set Metric and Imperial
The Planet Drill Gauge 2 Piece Set is a precision tool designed for drilling and hole-sizing needs, suitable for professionals and DIY enthusiasts.
£13.99 inc VAT

Planet Marking Gauge Rosewood
Planet Marking Gauge Rosewood
The marking gauge is made of selected rosewood with a protective lacquered finish, fitted with a brass knurled screw for more robust use. The gauge will mark with or across the grain.
£14.99 inc VAT
Planet Mitre Square
Planet Mitre Square
This Mitre Square has spring steel blade secured to a double brass faced rosewood stock with four brass rivets. The tool is used for the accurate marking of mitre joints at 45 degrees or 135 degrees.
£17.99 inc VAT

Planet Mortice Gauge Rosewood
Planet Mortice Gauge Rosewood
Mortice gauge performs two operations. One side of its posts has a single pin for general marking with the grain or on end grain; its other side has double pins adjustable to approximately 50mm for layout of mortices. Made with solid brass hardware, wear plates, and fitted with milled thumb screw in head. Overall length 200mm.
£18.99 inc VAT
Planet Protractor
Planet Protractor
Stainless steel protractor with high quality, clear, black graduations. Incorporates a 6” / 150mm rule. Degrees are marked from both ends of the scale.
£9.99 inc VAT

Planet Rotur Compass/Divider With Pencil HolderPlanet Rotur Compass/Divider With Pencil Holder
Planet Rotur Compass/Divider With Pencil Holder
Accurate Diameter Measurement: Easily measure turning blanks and workpiece diameters with precision for consistent woodturning results. Effortless Circle and Arc Drawing: Create flawless circular and arc-shaped designs, making it an invaluable aid in shaping wood pieces.
from £14.99 inc VAT
Planet Steel Square
Planet Steel Square
Conforms to BS939. Suitable for general workshop use.
from £5.99 inc VAT

Planet Try Square
Planet Try Square
Try square stock is made from best quality rosewood, spring steel blade & double brass facings. The blade is securely held by three brass rivets. Try squares are available in two sizes and can be used as external & internal square.
from £12.99 inc VAT
Planet Universal grinding gauge
Planet Universal grinding gauge
Assists in the regrinding of hand tools, drill bits, etc. Angles include: 90 degree int, 90 degree ext, 55 degree int, 60 degree int, 60 degree ext and 120 degree int. Made from stainless steel with clear, etched and inked graduations
£3.99 inc VAT

Steel Rule Metric & Imperial
Steel Rule Metric & Imperial
A high quality ground stainless steel rule. Quality etched and filled graduations. Single sided, metric/imperial.
from £0.99 inc VAT
Vernier Depth Gauge 8"
Vernier Depth Gauge 8"
This new depth guage has been designed for Planet with metirc and imperial measurements along the heavy duty rule and is tightened in place by a knurled thumbscrew through the body. Comes in a neat wooden box Depths of up to 8″/200mm can be measured.
£24.99 inc VAT

Planet Honing Guide
Planet Honing Guide
Holds chisels, plane irons etc. at a constant angle when using a bench stone for sharpening. Holds blades up to 3 1/2” wide. Supplied with instructions to obtain the correct bevel.
£13.99 inc VAT
'Tarrant' Light Pull Drive Replacement Stepped Drill Bit 3mm/6mm x 120mm
£12.99 inc VAT

PEN MANDREL SUPPORT CENTRE 1 MT
PEN MANDREL SUPPORT CENTRE 1 MT
The Pen Mandrel Support Centre has been designed and manufactured by PLANET here in the UK as an optimum way of holding and supporting the Pen Mandrel Shaft during the making of pens. This product is much the same as our Standard Rotating Centre (SD1/2), having 2 sealed bearings, a 12mm nose to represent 12mm bushings, is offered in 1MT & 2MT, precisely machined and designed to last and satisfy...
£29.99 inc VAT
PEN MANDRELL SUPPORT CENTRE 2MT
PEN MANDRELL SUPPORT CENTRE 2MT
The Pen Mandrel Support Centre has been designed and manufactured by PLANET here in the UK as an optimum way of holding and supporting the Pen Mandrel Shaft during the making of pens. This product is much the same as our Standard Rotating Centre (SD1/2), having 2 sealed bearings, a 12mm nose to represent 12mm bushings, is offered in 1MT & 2MT, precisely machined and designed to last and satisfy...
£29.99 inc VAT

Planet 11222 Large Drive Centre 2 Prong 1 1/2' (38.1mm) 2MT
Suitable for all large types of spindle work.Integral points will not work loose. Removable with extractor ring. 4 prong for squared spindle ends, 2 prong for out of square spindle ends.
£37.99 £26.49 inc VAT
Planet 11242 Large Drive Centre 4 Prong 1 1/2' (38.1mm) 2MT
Planet 11242 Large Drive Centre 4 Prong 1 1/2' (38.1mm) 2MT
Suitable for all large types of spindle work.Integral points will not work loose. Removable with extractor ring. 4 prong for squared spindle ends, 2 prong for out of square spindle ends.
£39.99 inc VAT

Planet Deluxe Rotating Centre
Planet Deluxe Rotating Centre
Deluxe Rotating Centre
£49.99 inc VAT
Planet Finial Support Mandrel Kit
Planet Finial Support Mandrel Kit
A brand new product designed by Planet. The Finial Mandrel fits into the tail stock and offers support for the fine end of a finial whilst turning the rest of it. The Finial Mandrel Kit has 3 Delrin (nylon type) inserts with 3 sizes 3mm, 4.5mm & 6mm hole depending on the size of Finial being turned. They fit into the inner race of a free running bearing. Available in 1MT & 2MT
£31.99 inc VAT

Planet Hollow Rotating Centre
Rotating centre with 5/16” bore for long hole boring.Based around our standard duty configuration. Also useful for spindle turning when there is a danger of a centre point splitting the stock. Set comprises: Hollow rotating centre, nose cone for use as standard centre, centring rod.
£47.89 £31.99 inc VAT
Planet Lathe Centre Alignment ToolPlanet Lathe Centre Alignment Tool
Planet Lathe Centre Alignment Tool
A brand new product from Planet. Aligns your headstock back with your tailstock after using it in 'outboard' mode.
£16.99 inc VAT

Planet LBD1 Lace Bobbin Drive Centre 1/2' (12.7mm) 1MT
Tapered drive for lace bobbins, etc. Mouth of drive is 1/2” square
£21.99 £14.99 inc VAT
Planet LBD2 Lace Bobbin Drive Centre 1/2' (12.7mm) 2MT
Tapered drive for lace bobbins, etc. Mouth of drive is 1/2” square
£22.99 £15.79 inc VAT

Planet LD1 Light Duty Rotating Centre  (60Deg) (22mm) 1MT
Planet LD1 Light Duty Rotating Centre (60Deg) (22mm) 1MT
Light Duty Rotating centre. Designed to facilitate the turning of small items. 22mm dia. head with 60 deg. point. Twin deep groove ball races.
£21.99 inc VAT
Planet Mini Drive centre
Planet Mini Drive centre
Mini Drive Centre With Integral Points 9mm x 4 prong
£14.99 inc VAT

Planet Piloted Drive Centre 1' (25.4mm)
1” diameter 4 prong head. Head relieved behind flutes to prevent binding. Supplied with inter-changeable point, pilot and hex key.
£32.99 from £22.59 inc VAT
Planet Standard Drive Centres 1MT
Planet Standard Drive Centres 1MT
Suitable for all types of spindle work.Integral points will not work loose. Removable with extractor ring. 4 prong for squared spindle ends, 2 prong for out of square spindle ends.
from £15.99 inc VAT

Planet Standard Drive Centres 2MT
Planet Standard Drive Centres 2MT
Suitable for all types of spindle work.Integral points will not work loose. Removable with extractor ring. 4 prong for squared spindle ends, 2 prong for out of square spindle ends.
from £15.99 inc VAT
Planet Tarrant Light Pull Drive Kit inc stepped drill 3mm/6mm x 120mmPlanet Tarrant Light Pull Drive Kit inc stepped drill 3mm/6mm x 120mm
£19.99 inc VAT

Planet Tarrant Light Pull Drive SPARE Stepped Drill 3mm/6mm x 120mm
Planet Tarrant Light Pull Drive SPARE Stepped Drill 3mm/6mm x 120mm
Planet Light Pull Drive Spare Stepped Drill 3mm/6mm x 120mm
£12.99 inc VAT
Page: | 1 | 2 |